Press Controls -
Metal Stamping


Press Controls -
Powdered Metal


Press Controls -
Forge


Die Protection


Programmable
Limit Switches


Tonnage Monitor


Brake Monitor


Shut Height
Control-Indicator


Counter Balance
/Cushion Control


Press Brake
Control


Light Curtains


Resolver


Motor Controls


Press Accessories


Production Tracking


Press Control
Survey





© 2005 Cieco Inc.
A Media Post Production


NOTE: If you question whether your press complies with current safety requirements,
give us a call. Our authorized representative or one of our technical support staff
will help you arrange an onsite survey of your press. Following the completion of the
survey, you will receive a report of the status of each press control. Call customer
service at 412-262-5581 to discuss your specific press control requirements.


You can complete this form online and submit it to Cieco for a quotation,
or print this survey and FAX it to Cieco at 412-264-9272.



The items marked with an asterisks are required fields.
*Company: *Contact:
*Address: *Position:
*City: *E-mail:
*State: *Phone:
*Zip Code: *Fax:

PRESS DATA
Manufacturer: Serial Number:
Press Capacity in tons: SPM:
Type: OBI/Gap Straight Side
Shut Height in inches: Slide Adjustment in inches:

If your machine is a Press Brake, complete the following: (Please check all that apply.)
Air Clutch, Single Speed Air Clutch, Two Speed
Friction Clutch w/Mechanical Linkage Friction Clutch w/Air Cylinder
Shoe Brake Band Brake

Press Motor Starters: (Please enter data in each field.)
MOTOR HORSE POWER VARIABLE
FREQUENCY DRIVE 		EDDY CURRENT REVERSE REPLACE/ADD
MAIN Yes No Yes No
SLIDE Yes Yes No
LUBE Yes No Yes No
OTHER Yes No Yes No
OTHER Yes No Yes No

Incoming Power Supply Voltage:
230vac 460vac 575vac Other

PRESS LUBRICATION SYSTEM
Automatic Recirculating Lubrication System: Yes No

Lube Pump Type: (Please check all that apply.)
120vac Single Phase AMPS
3 phase AC HP AMPS
Lube Solenoid

Lube Controller or Lube Timer: Yes No
Manufacturer Model
Electrical Schematic Available? Yes No

Sensors Used:
Low Lube Pressure High Lube Pressure Low Lube Level
Other Type Sensors, describe

Pulsed Grease Lubrication System: Yes No

Grease Pump Type: (Please check all that apply.)
120vac Single Phase AMPS
3 phase AC HP AMPS
Lube Solenoid

Grease Controller or Lube Timer: Yes No
Manufacturer Model
Electrical Schematic Available? Yes No

Sensors Used: (Please check all that apply.)
Low Grease Level Pulsing Sensor (Opens and Closes)
Other Type Sensors, describe

FLY WHEEL BRAKE Yes No
Manual and Mechanically Operated Air Operated with solenoid valve

SHUT HEIGHT CONTROL Yes No
Manually Adjusted Motor Adjusted (with up/down push buttons)
Would Prefer Automatic Adjustment:
Automatic Adjustment with linear transducer
Automatic Adjustment with multi-turn encoder

HYDRAULIC OVERLOAD SYSTEM Yes No
Please provide Electrical and/or Hydraulic Schematics when the order is placed.

DIE CLAMPING SYSTEM Yes No
Please provide Electrical and/or Hydraulic Schematics when the order is placed.

AIR COUNTER BALANCE Yes No
Manually Adjusted Automatic Adjustment
Would Prefer Automatic Adjustment

AIR CUSHION Yes No
Manually Adjusted Automatic Adjustment
Would Prefer Automatic Adjustment

DUAL SOLENOID CLUTCH/BRAKE VALUE REQUIRED Yes No

SAFETY LIGHT CURTAINS REQUIRED Yes No
If required: Protection Height
(Please check all that apply.)
Front Rear

MODES OF OPERATION (Please check all that apply.)
Off SwifTrip
Inch Bar
Single Jog
Continuous One Operator
Automatic Single Stroke Two or up to Four Operators
Continuous on Demand
Other (Specify)

RUN STATIONS (Please check all that apply.)
Use Existing Operator Station
Mounted on Console
Press Mounted (4 x 4 x 30)
Pedestal "T" Stand Mounted
Other

DIE PROTECTION
Number of Sensor Inputs Required:
8 16 Other:
Sensor Interface Junction Box

PROGRAMMABLE LIMIT SWITCHES
Number of Programmable Limit Switches Required:
2 6 8 16 24 32 Other:

TONNAGE MONITOR
Two Channels
Four Channels
Specify Strain Gage Cable Lengths:

SERVO-FEED INTERFACE REQUIRED Yes No
Servo-Feed Manufacture
Servo-Feed Model Number

OTHER REQUIREMENTS AND COMMENTS:

ENCLOSURE REQUIREMENT
NEMA with hinged door Console with sloped face

Control Panel Options: (Please check all that apply.)
Fused disconnect Variable frequency drives
Forward and Reversing Starters Choose the enclosure of your choice
Control Transformers Combine press control and motor control into one enclosure
Soft start drive
Panel Location: Door mounted buttons, key switches, etc. Side Mount buttons, key switches, etc

As you have viewed our website, which control best meets your requirements?
PPC1000 AUTOMATOR I
PPC1100R AUTOMATOR II
PPC1000R CIECO TO CHOOSE BEST CONTROL